Email Us : info@sfyh.com

0.66 inch OLED Display with 64×48 Resolution SSD1306BZ IC, 30PIN

SCE066001-V03 is a OLED Display with COG Type, 64×48 Resolution, SSD1306BZ IC, 6800/8080 interface 4 wire serial interface I2C, 30PIN

  • Resolution64×48
  • Outline Dimension (mm)18.46×18.1×1.21
  • Viewing Area (mm)15.42×12.06
  • Active Area (mm)13.42×10.06
  • Interface6800/8080 Interface/I2C/ 4-wire SPI
  • IC Part No.SSD1306BZ
  • ColorMonochrome (White)
  • PIN30
  • FPC typeconnector
Facebook Twitter Pinterest LinkedIn 分享


Basic Information

  • Display Color:                 WHITE
  • Dot Matrix:                      64×48
  • Drive IC:                         SSD1306BZ
  • Viewing Angle:               160°
  • Aperture rate:                 81.8%
  • Interface:                        6800/8080 interface, 4 wire serial interface, I2C
  • Outline Dimension:        18.46(W)x18.1(H)x1.21(D)
  • View area:                      10.196 (W) x 6.18(H)
  • PIN:                                30
  • FPC Type:                      Connector





General Specification


ITEM SPECIFICATIONS UNIT
 MODULE SIZE 18.46(W)x18.1(H)x1.21(D) mm
 VIEWING AREA 15.42 (W) x 12.06(H) mm
 ACTIVE AREA 13.42 (W) x10.06(H) mm
 DOT SIZE 0.19(W) x0.19(H) mm
 DOT PITCH 0.21(W) x0.21 (H) mm
 ASSY.TYPE COG ---
 WEIGHT TBD



Interface Definition


PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC
NC.
2 C2P
C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC
NC.
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 NC
NC.
11 BS1 I Bitmap Interface selection pins.
12 BS2
13 CS# I Chip Select input pin. Active "L"
14 RES# I Hardware reset input pin. Active "L".
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor's Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 NC
NC.
30 NC
NC.


Next Product
Prev Product
Product Tags oled module          oled module 128x64          color oled module          oled module arduino          128x64 oled module          OLED Display Module          oled screen module          transparent oled module          round oled module         

INQUIRY

Contact us for all information about the product

click here to leave a message
leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.