General Electric FCGD Mark V Turbine Control DS200FCRRG1AKD PLC Module


GE MARK V FIRING CIRCUIT BOARD






Contact: Miya

Job Title: Sales Manager

Skype: live:miyazheng520

Email: sales@amikon.cn 

Tel: 86-18020776792(Whats App )

QQ :2851195450 

Company profile:

We are a professional engaged in the global well-known brands (DCS system, robotic system, large) servo control system module, spare parts sales enterprises, 


the company product content is: the distributed control system (DCS), programmable controller (PLC), MOTEOROLA - MVME industrial converter (Anybus) modules, industrial control, 

communication, remote I/o module (RTU), industrial computer (IPC), low frequency screen (IPC) for industrial use, SCSI interface (50/69/80 pin) Anybus (Gateway). 

The spare parts we sell all provide a year of quality assurance, and have been strictly tested and certified, has become a global industrial automation spare parts and parts sales enterprises.




DS200FCRRG1AKD

Product Description

The GE Firing Circuit Control Board DS200FCRRG1AKD features 1 terminal block  with terminals for 95 signal wires. 

It also contains 10 2-pin connectors, 2 ribbon cables, and a programmable logic device. The IDs of the 10 2-pin connectors 

begin with a numerical value and end with PL. 

The numbers are assigned in sequence and are printed on the surface of the board for easy reference by the installer or servicer. 

For example, some of the IDs are 1PL, 5PL, 12PL, and 15PL. 

Because of the number of 2-pin cables attached to the connectors, it is important to record where the cables are attached before you disconnect them. 

Mark on the cables the ID of the connector it is attached to before you disconnect it. Then, when you are prepared to connect the cables on the replacement board, the task is fast and accurate. 

If you connect the 2-pin cables to the wrong connectors, you might not realise the error until you attempt to start the drive. This leads to more down time for the drive and a loss of productivity 

for the drive and other related activities performed at the site.

To remove signal wires from the terminal block, have on a hand a narrow flat blade screwdriver. Loosen the retention screw and pull out the signal wire. Make sure the signal wire 

has about 0.5 inches of insulation removed from the end of the wire. Best practice is to have all the bare wire inserted into the terminal. 

However, if less than 0.5 inches of insulation is removed, the connection might not be made between the terminal and the signal wire.  



Related recommendation
GE IS200VGENH1B AB 1746-HSCE
GE IS200TRPGH2B AB 1775-GA
GE IC697PWR711 AB 1769-IF16C
GE IC697CMM711 AB 1769-IT6
GE HE693IBS100 AB 1606-XLS120E
GE 531X305NTBAPG1 AB 1794-PS3
GE IC697MDL340 AB MVME162-262
GE DS200SDCCG1AGD DS215SDCCG1AZZ01B AB 1766-L32BWA
GE IC697MDL740 AB 1746-OW8
GE IC697MDL350 AB 2711-B5A10

Contact: Miya

Job Title: Sales Manager

Skype: live:miyazheng520

Email: sales@amikon.cn 

Tel: 86-18020776792(Whats App )

QQ :2851195450 





Waiting for your inquiry.





Product Tags General Electric IC695CPE330          General Electric IC693PIF400          General Electric IC693PTM101          General Electric IC693TCM302          General Electric IC693ALG391          General Electric IC693CMM301          General Electric IC697MDL654          General Electric IC697MEM713          General Electric IC693ALG221         

INQUIRY

Contact us for all information about the product


click here to leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.